Navigation¶

• Main Page
  

• Random Page
• Create a new Page
• All Pages
• Categories
• Navigation Paths
  

• Administration
• File Management
  

• Create Account
  

Rigging Hardware

Main¶

Mast¶

• 4 Schaefer 34-46 halyard exit plates - On Hand
• Mainsail track gate - Need to cleanup
• Spinnaker pole lift - Need to cleanup
  • Padeye 2-3/8" (c-t-c) 3" width x 1-1/4" high (rise) - Need to cleanup
  • Swivel Block 2" dia x 1/2" width
• Spinnaker Track - Now 18'
  • 6' (5'11" ?) 1-1/4" T-Track
    • 2 end caps
  • 1 5-3/4" Cleat
  • Forespar spinnaker car - Pin End fitting - On Hand
  • ?? spinnaker car - Ring end fitting - On Hand
  • Slider mounted check block 1-1/2" length x 1/2" width - Garhauer 25-22SB - Need to Buy
  • Investigate Rigrite fittings (maybe just sleaves)
  • Good article on Carbon Fiber Poles
• 1 5" cleat (labeled Bottom Spinnaker Track) huh?
• 1 5" cleat for halyard
  

Boom¶

• Gooseneck with reefing hooks - Needs to be reworked to include Clew Shackle
  • Check out the measurements and pics on Rigrite
  • See Jack's post to have a new one built
• Outhaul
  • Outhaul Slider - See Rigrite - Need to Buy
  • 1 brass cheek block 1" Dia. 1/4" width for outhaul
  • Outhaul line (was rope to wire) - Need to Buy
• 3 Boom Bails and Blocks for Main sheet - Sand and cleanup
  • Bails - 4-1/8" width x 4-3/4" length
  • Single Block - 2-3/8" x 11/16" width
• 2 5" cleats for reefing
• Clew shackle
  • Has little nibs on it
  • 1" width x 2" length
• 3 Plate mounted padeye 2-1/4" (c-t-c) x 3-1/8" length x
• 2 Ronstan Australia RF1379 cheek blocks
  • Curved mounting
  • 2" dia x 1/2" width
    

Masthead¶

• 4 Sheaves 4-3/4" diameter 5/8" thick 5/8" Dia. post - On Hand
• 2 Sheave pins - 5/8" dia - On Hand
• Bolt for shroud tangs - 3/4" dia x 6-3/4" length
• Spinnaker Halyard Block - 2-3/8" dia x 3/4" width (Fico Australia FG1126)
  • no swivel
  • U-Bolt 3-1/4" long x 1" wide (c-t-c)x 3/8" thick
• Halyard Restrainer for jib halyard - On Hand
• Solent Tang placement 24" from masthead
  

Mizzen¶

Mast¶

• 2 Schaefer 34-46 halyard exit plates - On Hand
• 1 15" x 1" T-Track for mizzen boom gooseneck - Replace
  • Site on 15-1/2" long by 3/8" wide (square) riser - Keep
  • 2 track end caps
• 2 Shroud brackets
• 1 Mizzen sail track gate - Needs to be cleaned up
• 1 5" cleat
  

Boom¶

• 2 - bails 3" wide x 4" length
• 2 plastic cheek blocks 1-3/8" Dia. 1/2" width
• Outhaul
  • Shaefer Outhaul slider\block - See Rigrite
  • 1 brass cheek block 1" Dia. 1/4" width for outhaul
  • Outhaul Line (was line\wire) - Need to determine size
• 1 End of Boom hanger
• 1 Gooseneck slider with Reefing hooks
• 1 Other fitting (u bracket with two bolts)
  

Masthead¶

• Sheaves 2" diameter x 1/2" thick - On Hand
  • Wide head cotter pin - 1-1/2" length x 1/4" dia - S/J 370271 - Need to buy
• Bolt for Shroud Tangs - 5-1/4" length x 1/4" dia - On Hand
• Water proof cable exit
• Mizzen staysail halyard block
  • Bow Shackle - 1" width x 2" length - w\ New Sails
  • Swivel Block - 2" dia x 1/2" width - w\ New Sails